For a complete STRIDE WIDE System you will need to purchase [2] End Pieces, QC Part #250327, and [1] 34" Sani-Clip, QC Part #250336. To increase the width, you will need to purcase Center Pieces, QC Part #250329 and [1] additional Sani-Clip for each Center Piece ordered. Disinfectant is sold separately, see below for suggestions.

Color of included insert mat may vary from photo.

Add additional width to your SaniStride STRIDE WIDE Disinfectant Mat with this Center Piece. Included is one center section and a 1" insert mat. The minimum required for a WIDE Disinfectant Mat system is two end pieces and a Sani-Clip, so when ordering, you will also need to purchase two end pieces, as well as a SaniStride 34" Sani-Clip, QC Part #250336.

The STRIDE WIDE RUNNER is a modular mat system to create a WIDE Shoe Sanitizer Runner Mat as needed. The minimum size WIDE runner consists of 2 enter/exit end ramp sections, with a 1″ wide, 1/2″ high strut between, held together with a Sani-Clip. The minimun wet sanitizer surface is comprised of 2 sections of 18″ L x 34″ W, for a total 36″ L x 34″ W. The ramp around the merged sections is 2.5″ wide, creating an overall outside runner length of 42" x 39" in a two-piece system; 1” is added for each strut in the Runner System.

By adding these 18" L x 34" W WIDE CENTER runner sections, you can create a runner as wide as desired. Each additional section creates another 1″ wide 1/2″ high center strut. An additional Sani-Clip is required for each additional center section added.

It is suggested to charge each 1″ STRIDE insert with 1 to 1.5 gallons maximum of sanitizer. Because of the proprietary insert design, there are no waves and little-to-no splashing, making the SaniStride System one of the best sanitizing foot bath mats on the market.

Simple Sanitizer Mat Clean-Up

• Simply flush/rinse the insert & base mat with clean water in a utility sink or with a hose
• Stand or hang the insert on-end to drain the water quickly & drip-dry overnight
• If you desire/need to use the system 24/7, you will want to order a replacement insert, QC Part #250321, with your initial order - it is needed to the cleaning rotation process as one will need to drip overnight
• Do NOT put the insert in an extractor, washer or dryer as they will destroy the insert & its inner material

Charging the STRIDE WIDE Mat System

1. Dilute the quaternary concentrate or other non-chlorine concentrate by mixing the specified quantity of concentrate with 1 gallon of water. Please follow dilution rates per the manufacturer’s label. Typically a ratio of 1-2 oz of concentrate per gallon of water. Ready to use sanitizers (already diluted with water) can be added directly to the mat, but are very expensive to use in the SaniStride Systems
2. Set the STRIDE system on top of a 4’ x 6′ min, or larger dry mat in the place where it is to be used. The dry mat will protect the flooring from effects of prolonged exposure to the sanitizer, as well as help prevent slipping & falls as the bottoms of the shoes will be very wet when exiting the STRIDE mat and will need to be wiped dry. You can also place a smaller dry mat at the enter/exit side of the SaniStride mat to dry shoes when floor finish is not a concern.
3. Pour 1/2 a gallon of diluted sanitizer slowly onto the insert directly at the start of charging. It will take a few minutes for the liquid to disperse throughout the entire insert. Once the initial liquid settles, pour the remaining 1 1/4 to 1 1/2 gallons max onto the insert. Let this settle again, being careful to not overcharge the system, as doing so will likely cause splashing & overflow over the base mat walls and onto the floor.

Due to Evaporation & Shoe Wicking the amount of sanitizer in the STRIDE systems will need to be assessed for proper saturation from day to day by noticing a slight puddle around the outside of the shoe sole when stepped on. If a puddle is not apparent, add a half quart and retest. Add more until slight puddle reappears around sole being careful not to overcharge.

Ask Your Chemical Supplier or Manufacturer how long the sanitizer will be effective once exposed to air and the contact time necessary to achieve the effectiveness of the sanitizer. Adding sanitizer as needed day to day will assist in keeping up the potency of the chemical to a certain extent, but a complete clean out will need to be performed at regular intervals. Check the labels for this information as well

Rinse Insert With Clean Water by hose or in a utility sink and stand on end to drip dry over night before recharging. DO NOT put the insert in a dryer or extractor as these machines will damage the insert.

Insert color may vary from photo